Technical rubber programs built around lean sourcing, controlled specifications, and documented compliance. Request support
Rubber engineering article header

2026-11-13

Momentive Silicone Materials: 6 Questions That Actually Affect Your Order

A buyer-side FAQ on Momentive silicone rubber, the GE lineage, two-shot molding, silicone glasses, and PVC foam board — written from seven years of documented order mistakes, not marketing decks.

I've handled silicone materials orders for seven years. I've personally made and documented about a dozen mistakes that cost real money — somewhere around $4,000 in redos, delays, and scrap. Now I maintain our team's pre-check list so nobody repeats them. This is the FAQ I wish someone had handed me in 2018.

Below are the six questions that come up on almost every Momentive-related inquiry, plus a couple of adjacent ones buyers ask when they're not sure silicone is even the right material. Short answers, direct. No fluff.

1. What exactly is “Momentive silicone rubber,” and who is it for?

When buyers say “momentive silicone rubber,” they're usually referring to the high-consistency rubber (HCR) and liquid silicone rubber (LSR) lines — elastomers that hold properties across roughly -60°C to +200°C continuous, with short excursions higher depending on formulation. Standard thermoplastics don't survive that range, which is why silicone shows up in gaskets, seals, medical components, automotive underhood parts, and electronics potting.

The classification matters more than the brand name. Most silicone elastomers get sorted under ASTM D2000 line callouts, which encode heat resistance, oil resistance, and physical property targets in a single spec line. If your RFQ doesn't reference an ASTM D2000 designation (or a drawing with equivalent detail), you're leaving the door open for a supplier to interpret “standard” however they like. That's not a Momentive issue — it's a specification issue. But it shows up constantly on Momentive-material orders anyway.

I'm not a polymer chemist, so I can't speak to crosslinking chemistry or formulation trade-offs. What I can tell you from a procurement perspective is this: know your temperature exposure and your durometer tolerance before you ask for quotes. Those two numbers drive most of the cost difference.

2. What does “Momentive GE silicone” mean — does the GE history still matter?

Momentive's silicone business traces back to GE Silicones, which was carved out and rebranded in 2006. Engineers who've been specifying materials since the 1990s still write “GE Momentive” or “GE silicone” on drawings, and that legacy carries real weight — the formulations and certifications didn't disappear when the name changed.

Here's the catch I ran into in 2021: a supplier sent me a datasheet stamped “GE Silicones” with a revision date from 2003. The material might have been perfectly fine, but the document was older than some of my colleagues. I had to go back and request current MOMENTIVE-branded documentation, which added nine days to the approval cycle because the supplier had to pull it from the factory. That's a $0 mistake in direct cost and a painful one in schedule.

If you see “GE Momentive” on a quote or drawing, treat it as a signal to verify the documentation date, not a signal that the material is obsolete. Legacy spec, current paperwork — that's the rule.

3. When should I use silicone-thermoplastic two-shot molding instead of overmolding?

Two-shot molding (sometimes called 2K) means both materials go into the same tool and bond in one cycle. Overmolding means you mold the thermoplastic substrate first, then add silicone in a second operation — often with a primer, and often with a bonding failure risk if the surface prep is inconsistent.

The reason two-shot matters for silicone is adhesion. Silicone doesn't naturally stick to most thermoplastics, so a mechanical interlock or a compatibilized bond is doing the real work. Two-shot lets you form that interlock in-tool, cycle after cycle, without manual priming steps. The trade-off is tooling cost — typically 1.5-2.5× a single-shot tool — and material compatibility constraints. Your thermoplastic has to survive the silicone cure temperature, which rules out a lot of commodity resins. Polybutylene terephthalate, polyamide, and PPSU are common pairings for a reason.

In my first year, I made the classic two-shot error: assumed “two-shot compatible” meant any thermoplastic would bond to any silicone. It cost us a $2,300 tooling deposit and three weeks before the molder told us the resin wouldn't survive cure. Now I ask for a material pairing table before I approve any two-shot quote. Every time.

4. Silicone glasses — what specifications do buyers actually get wrong?

Silicone components on eyewear (nose pads, temple tips, sometimes full frames) live or die on three specs: durometer, skin-contact compliance, and UV stability. Durometer for nose pads usually sits in the Shore A 40-60 range — soft enough to grip, firm enough not to collapse. Anything outside that band and you'll hear about it from wearers within a week.

Skin-contact compliance is where I see the most hand-waving. “Medical-grade silicone” is a marketing phrase, not a standard. Ask for the actual test reference — ISO 10993 for biocompatibility, or USP Class VI for the US market. If a supplier can't name the standard, they're hoping you won't ask.

UV stability is the quiet killer. Silicone itself is fairly UV-resistant, but pigments and additives aren't always. Clear or light-colored pads that yellow after two months on a retail shelf look cheap (unfortunately, and that's a brand perception problem, not just an aesthetic one). Request accelerated weathering data before you commit to a color match.

Worse than expected? Yes, the first time. A lesson learned the hard way.

5. What is PVC foam board, and why do silicone buyers keep asking about it?

PVC foam board is a rigid, closed-cell foamed polyvinyl chloride sheet — typically 0.4-0.8 g/cm³ density — used for signage, cabinetry, exhibition displays, and anywhere you need a lightweight structural panel that cuts and machines easily. It has nothing to do with silicone chemically. Zero overlap.

The confusion comes from the word “foam.” Silicone foam and PVC foam board both get called “foam,” so buyers searching for one sometimes land on the other. If you need compressible sealing, thermal insulation, or fire-rated gasketing, you're probably looking at silicone foam. If you need a flat panel that holds a screw and takes vinyl graphics, PVC foam board is the answer. Different problems, different materials.

Don't hold me to this, but I'd guess a third of the “silicone vs. PVC” questions I get are actually people who need a foam panel and got routed to a silicone supplier by a search engine. Worth checking the application before the material.

6. What's the single biggest mistake buyers make on silicone specifications?

Trusting the datasheet without incoming inspection. That's it. That's the mistake.

Datasheets describe a material, not a batch. In 2022 I approved a 2,000-piece LSR order against a datasheet durometer of 50 ± 5 Shore A and skipped the incoming check because the supplier had a good track record. The parts that arrived measured 57-59 on our durometer. Technically inside the tolerance band, practically too hard for the application. $890 in rework plus a one-week production delay — and the supplier wasn't wrong, because the spec allowed it.

Now our checklist requires three things on every silicone receipt: a durometer check on a sample of at least five parts, a cure-state check (silicone that isn't fully cured will feel tacky and fail compression set later), and a documentation cross-check against the current revision. We've caught 47 potential issues with that checklist in the past 18 months. Most were minor. Three would have been expensive.

None of this is exotic. It's just the discipline of not assuming “Momentive material” means “Momentive-quality batch.” The brand on the box tells you what was supposed to happen. Your inspection tells you what actually did.

Cooper Tire editorial note

Rubber sourcing decisions should be tied to measurable application facts. If a post raises a question about material choice, compliance files, or qualification planning, send the use condition and drawing for a practical review.

Previous: The $23,000 I Lost Chasing 'Cheap' 2-Inch Silicone Hose — And What I'd Do Differently Next: Why Cheap Small Plastic Orders Keep Coming Back Wrong